Home > Buffalo Linkstation > Buffalo Error I18

Buffalo Error I18

Contents

Related Posted on July 17, 2011, in Buffalo Quad Pro NAS. I36 Cartridgex I36 Decryption error Media cartridge cannot be decrypted. After formatting, if the error still appears after rebooting, replace the hard drive. Note: Do not turn off the power during the updating process. - I26 Web Setting I26 Initializing Initializing all settings. - I27 USB Diskx I27 Checking Checking USB hard drive X. navigate here

At this point the system goes into RAID array "Repairing" mode as it rebuilds the data onto the new disk. I47 SYETEM I47 Don't Power Off I48 FailOver I48 PushFuncToStart This TeraStation is ready to become the failover backup for the main TeraStation. Could the drives being different sizes be causing this? I49 FailOver I49 LostMainTarget The main TeraStation in the failover configuration cannot be found.

Buffalo Linkstation Error Codes

Joseph Lo | October 31, 2014 at 5:48 am Maybe just need an update to b the firmware. To be safe, I would suggest you first copy the data off the raid array before proceeding further. Dez 2012, 17:44 Beiträge der letzten Zeit anzeigen: Alle Beiträge1 Tag7 Tage2 Wochen1 Monat3 Monate6 Monate1 JahrSortiere nach AutorErstellungsdatumBetreff AufsteigendAbsteigend Seite 1 von 1 [ 9 Beiträge ]

  • The fan is spinning too slowly or has stopped.
  • If you are at an office or shared network, you can ask the network administrator to run a scan across the network looking for misconfigured or infected devices.
  • The media cartridge may have been encrypted by a TeraStation other than this product.
  • Delete or move some of the stored video.

Ein Nutzer, der erfolgreich eine defekte HDD in seinem Raid 1 getauscht hat, wird sich sicherlich nicht hier melden. Email Reset Password Cancel Need to recover your Spiceworks IT Desktop password? Hopefully someone who has done a rebuild of this type will see this and post an opinion about the timing. Buffalo Linkstation Flashing Red Light 3 Times I52 A new firmware version has been released.

Tried many restarts. Buffalo Linkstation Flashing Red Light Do not turn off the TeraStation power. Sorry. Move the TeraStation to a cool location.

For details, see the separate sheet "Hard Drive Replacement Procedure". Buffalo Linkstation Solid Orange Light Boris Shen | September 24, 2014 at 1:25 pm Are you Australia Based? we had a hard drive fail a few months back and with it having 4 x 1.5TB drives i didnt want to spend twice as much getting a 1.5TB when we The system will now be shut down safely.

Buffalo Linkstation Flashing Red Light

A technical consideration would be to choose to have identical drives, both in storage size and firmware version, as it is entirely possible you have discovered a 'feature' that causes frequent This can take a long time - typically about 6+ hours on a 1TB system, and longer with larger arrays. Buffalo Linkstation Error Codes Join the community Back I agree Powerful tools you need, all for free. Buffalo Linkstation Flashing Red Light 7 Times I would also be very concerned that the drives are "very hot" as you describe, in a data centre.

Joseph Lo | July 28, 2014 at 9:22 pm Hi Sebastian, I would believe that your data in the raid 5 array is safe given that you said the problem drive http://drupalmostpopular.com/buffalo-linkstation/buffalo-hdd-error.html Reply Subscribe RELATED TOPICS: I12 Error on LS-WXL Running Raid Array Buffalo TeraStation 3, Disk error status 48 Adding a new drive to linkstation 421 and change RAID conf   8 I33 Replication I33 ReplicateFailure An error occurred in replication, or synchronization between the main TeraStation and the backup TeraStation failed during failover configuration. USB device is dismounted (lights for 5 seconds). Buffalo Linkstation Info/error Solid Orange

Aug 28, 2013 at 1:09 UTC A chkdsk doesn't really tell you if a drive is good or not.  The drive may well be fine, but personally I wouldn't trust it i came to the conclusion that they were not over the maximum operating temperature though. Information code Descriptions E04 Firmware is failed. http://drupalmostpopular.com/buffalo-linkstation/buffalo-ls-wvl-error.html Die LS-VL ist das schnellste Gerät. 75/45 MB/sWer seine Daten unbedingt durch Raid vernichten will kann den gleichen Prozessor in der LS-WVL bekommen.Ich poste es so oft ich kann.

I37 Recovery I37 SystemRecovering System recovery in progress. - I38 Recovery I38 RecoveryFinished System recovery is complete. - I39 Recovery I39 Change Boot System recovery from the USB recovery device is Buffalo Terastation Error Codes Check your settings. Set the hard drive again after shutting down the LinkStation.

Hier nutze auch ich keine USV.Optimistisch denkend hoffe ich mal du hast Recht.

I16 The RAID array is being created. If the antivirus software is configured to delete viruses from the quarantine folder automatically, then the message will not be displayed. I27 Checking a USB hard disk. Buffalo Em Mode I35 Cartridgex I35 Location error A hard drive set as a media cartridge has been installed in the drive 1 slot.

If the error is displayed again, contact Buffalo technical support for assistance. If the error still appears after formatting and restarting, replace the hard drive. Mo 31. weblink Aug 27, 2013 at 5:11 UTC Lucas7589 wrote: It worked for a few weeks and then died again, get a i18 rebuilding array error and the NAS device becomes unresponsive.

During that period the raid array is not accessible via the network. I32 Appears when RAID rebuilding or formatting on the web Admin interface is necessary after replacing the hard drive. When you do so, the system thinks for a minute or so while the RAID array is altered to put the new disk into it. I18 The RAID array is being reconfigured. *Data transfers will be slower than usual until this is complete.

Lights during initialization. Update the firmware. Blinking Blue The LinkStation is starting up or shutting down. Replace hard drive X.