Home > Buffalo Terastation > Buffalo Terastation Hd Error E23

Buffalo Terastation Hd Error E23


Ensure the power supplied to the UPS, and if there is no problem, turn on the power for the LinkStation. The number of flashes is the tens place of the error code.  I23 1s place of information code The LED illuminates for 0.5 seconds every 0.3 seconds. Text Quote Post |Replace Attachment Add link Text to display: Where should this link go? E11 Fan Error. navigate here

The number of times of short flashing (flashing in 0.3 secs: ) is in the 1s place of the error code (E23). E15 Hard drive cannot be found. The number of flashes is the ones place of the error code. Its located in a server rack at a data center, when replacing the drive i noticed the drives being very hot.

Buffalo Terastation Error Codes

Function LED Display Status Solid Blue DirectCopy is ready (lights for 1 minute). Good luck! The hard drive is not connected, or maybe failed.

  1. The error still persists, contact BUFFALO's service center for repair.
  2. Joseph Lo | August 12, 2014 at 6:51 am Hi Sammy.
  3. I21 Checking the hard drive.
  4. All Rights Reserved.
  5. Following this you cannot use the hard drive.

If the error still persists, contact Buffalo's service center for repair. A technical consideration would be to choose to have identical drives, both in storage size and firmware version, as it is entirely possible you have discovered a 'feature' that causes frequent Replace the failed drive indicated by the red LED. Is this more likely to be a hard drive controller issue?Any thoughts or suggestions out there would be much appreciated!Rod Top Profile Reply with quote Display posts from previous:

Please tell us how we can make this answer more useful. Buffalo Terastation Support I have just had an error on mine and am wondering if you can help - the red LED is blinking indicating that there is a problem in drive 1 My Replace the hard drive. Buffalo NAS-Central ForumsWelcome to the Linkstation Wiki community Register Login FAQ Search It is currently Fri Nov 18, 2016 10:37 am Unanswered posts | Active topics Board

E22 Mounting of the hard drive failed. I19 The RAID array is being erased by filling 0 in the array. About three months ago, with advice from this forum, I swapped out the original 500gb drives and put in four 1.5tb drives (using the method to save the existing drive data). Click here to see how to solve it.

Buffalo Terastation Support

How long did you wait to let it rebuild before rebooting?  With drives of that size a rebuild can take a long time, especially if you are using a parity RAID Format the hard drive. Buffalo Terastation Error Codes Buffalo Americas prides itself on offering best in class support for your products. Buffalo Terastation Default Password Logged davo Really Big Bull VIP Posts: 5391 Re: TeraStation II Pro Raid Error E13 « Reply #7 on: April 09, 2016, 06:20:26 pm » The terastation pro II hasn't been

When rebooting the TeraStation, it will run as degrade mode when RAID 1 or RAID 5 is used. check over here Clickhere for details. Excessive heat can lead to early and/or unexpected equipment failure and drive failure, and may cause data read/write corruption in some systems due to heat building up in areas of your After the LinkStation shuts down.

Temperature in the system may be over the limits of warranty. I17 The RAID array is being resynchronized. *Data transfers will be slower than usual until this is complete . E16 Hard drive cannot be found. his comment is here Bookmark the permalink. 8 Comments. ← Life with the Ipad 2 - part1 Buffalo Quad Pro and Shonk's Firmware v1.43mod1c → sebastian | July 28, 2014 at 10:24 am Hello Joseph,

Email *Required Your Feedback *Required Refine your search Select Product / OS & Hardware Select Product Select OS & Hardware Enter Keywords or a specified ID BUFFALO_GLOBAL BUFFALO GLOBAL [EUROPE] English| Contact Buffalo technical support for assistance. Join Now For a while now our TS-RHTGL/R5 Terastation pro has been playing up.

Replace Xth hard drive.

If the INFO/ERORR LED (the POWER LED for LS-QVL series) is tuned off after the product is rebooted, the restoration has been completed. Place of information code Status Display example 10s place of information code The LED illuminates for 1.0 seconds every 0.3 seconds. Email Reset Password Cancel Need to recover your Spiceworks IT Desktop password? S.M.A.R.T.

Please tell us how we can make this answer more useful. Do not place objects in the area around the LinkStation, or install at a cooler location. E12 The system temperature has exceeded the safety value. http://drupalmostpopular.com/buffalo-terastation/buffalo-terastation-pro-error-e04.html Click [Resynchronize] under [System] - [Backup] - [Replication] in the Web Admin interface.

Post new topic Reply to topic Page 1 of 1 [ 1 post ] Print view Previous topic | Next topic Author Message solsurfer Post subject: Faulty HD?PostPosted: Wed Mar Yes No Thank you for your cooperation in the questionnaire. I11 The invalid sectors of the hard drive may reach a dangerous level. Aug 27, 2013 at 5:09 UTC Lucas7589 wrote: Also forgot to mention that i decided to see if the hard drive removed was actually dead.

Aug 27, 2013 at 5:11 UTC Lucas7589 wrote: It worked for a few weeks and then died again, get a i18 rebuilding array error and the NAS device becomes unresponsive. E13 An error occurred in the RAID array. The message is coded by the pattern of blinking. About Advertising Privacy Terms Help Sitemap × Join millions of IT pros like you Log in to Spiceworks Reset community password Agree to Terms of Service Connect with Or Sign up

The number of flashes is the ones place of the error code. http://www.buffalotech.com/select-your-region After updating firmware, the INFO/ERROR LED (the POWER LED for LS-QVL series) is flashing in orange. (I12: it runs in the degraded mode). Examples of LCD Meaning Resolution E00 SYSTEM Error MPU No Response System is not responding. Hard drives may be not connected or may be damaged.