Home > Buffalo Terastation > Buffalo Terastation Pro Error E23

Buffalo Terastation Pro Error E23

After about 3 months of usage the unit began to crash. Error EC8F03ED: Cannot create the recovery point. I'm assuming a table fan pointing in the best direction towards the station isn't gonna do much as the whole thing is quite well enclosed. E12 SYSTEM Error Cooling Failure Temperature in the system is over the limits of warranty. navigate here

E01 Error on DRAM DATA LINE E02 Error on DRAM ADDRESS LINE E03 Error on RTC CHIP E04 Failed to load kernel (FLASH error) E05 SYSTEM STOPPED E10 UPS AC LINE FAULTY AGAIN!!PostPosted: Sat Sep 20, 2008 1:59 pm Offline Moderator Joined: Tue Jul 26, 2005 5:22 pm Posts: 1123 Location: United Kingdom It sounds as though something has got corrupted on Could my symptoms match with the odd power cut?Thanks also to ciscokidinsf for your quick reply. The TeraStation then sent me emails via that address.

One extra question though. Buffalo Terastation Pro II Data Recovery Data recovery including error in a RAID Array with 4 flashing/blinking red led lights, or SATA hard drive failure. Replace the hard drive. If the error still persists, contact Buffalo's service center for repair.

The case has the screws through the 4 feet at the bottom and 3 screws at the back holding it in place. Where I live in Vietnam, it is very hot. At the moment I'm trying the box with the front unlocked and open with a small fan blowing straight into the HD's. FAULTY AGAIN!!PostPosted: Sat Sep 20, 2008 2:36 pm Offline Newbie Joined: Fri Aug 08, 2008 3:03 pm Posts: 14 Hi Itimpi....I had hoped I would never be conversing with you again!

Thank you so much for your quick responses. However, I think your setup is different to mine cos there are no jumpers in any of my HD's and I did buy the same HD as the other 3 and What?! Replaced Disk.

Well..I have backups which I can use but it makes running my business ALOT easier so...fingers cross we can find a solution.Regards, Zac.I have just completed a 5GB transfer to an Buffalo often advise to update the firmware but the system still boots into Emergency Mode and EM482 even with the Debug options. Examples of LCD Meaning Resolution E00 SYSTEM Error MPU No Response System is not responding. Anyhoot...I got myself a feather duster and laced it with WD40 and gave the inside the once over.

  1. New and even more sophisticated computer software packages are popping out that happen to be generally created or meant to operate on new pcs.
  2. E23. … Terastation Pro Error E14.
  3. E11 SYSTEM Error Fan Failure There is a problem with the number of fan spinning.
  4. The firmware is corrupted.

After the unit crashed my procedure was to force power off, disconnect the power cable and network cable, take out all the hard disks and leave the unit to cool and To be safe, I would suggest you first copy the data off the raid array before proceeding further. Reattach the USB device to the LinkStation. The error still persists, contact Buffalo's service center for repair.

RAID arrays can fail. http://drupalmostpopular.com/buffalo-terastation/buffalo-terastation-pro-error-e05.html The system looks very flaky. If the error still persists, contact Buffalo's service center for repair. In the 20 minute transfer it stalled about 5 times but the transfer completed ok.

Top Profile Reply with quote itimpi Post subject: Re: HD1 Faulty. Please do the following if this happens:

Shut down the LinkStation. Strange. http://drupalmostpopular.com/buffalo-terastation/buffalo-terastation-pro-error-e04.html Since one of these is a temperature alert that might give you an indication as to whether that is happening.

I suppose the only thing I could do to really keep the temperature down would be to install air con. I couldn't beleive it. msc in Start Menu Search Box, hit Enter.

Buffalo Americas prides itself on offering best in class support for your products.

Don't waste yourtime. And that was about a week ago. TeraStation™ Pro Key Specifications | Processor … Buffalo TeraStation™ Pro is a larger capacity NAS device with robust RAID 6 capability. Try rebooting the TeraStation 4 or 5 times until the TeraStation will boot up in EM mode, and update the firmware.

mac telnet to terastation. Well....the HD that I replaced I've filled completely and then copied COMPLETELY back onto the buffalo so....I gotto say...I think it's fine. Therefore if your computer is currently more mature than five years, it can be hugely suggested that you just buy a new one particular, that may be if all of the weblink Replaced Disk.

The message is coded by the pattern of blinking. Details Products OS / Hardware Was this answer helpful? Or I might get my local computer dude to build me a new computer that holds 5X500gb SATA HD's!! After formatting, reboot the system.

FAULTY AGAIN!!PostPosted: Sat Aug 09, 2008 10:46 am Offline Moderator Joined: Tue Jul 26, 2005 5:22 pm Posts: 1123 Location: United Kingdom Zac wrote:I have just completed a 5GB transfer to I am using the first failed disk as external storage formatted to NTFC and it works PERFECTLY. After replacement, rebuild the RAID array by following the setup screen after starting the LinkStation. Thanks.As a sidenote, I forgot to mention that we have frequent power cuts here.